vltor.comの競合サイトトップ10

primaryweapons.com

primary weapons systems – evolve

ar15discounts.com

If you’re considering adding a suppressor to your firearm setup, you probably have a lot of questions — and for good reason. From legal requirements and ATF approval timelines to choosing the right suppressor for your caliber, there’s a lot to navigate. This comprehensive FAQ is designed to help you understand the ins and outs [...]

revivaldefense.com

Call us old fashioned, we like our castle nut staked to prevent it from rotating loose on the receiver extension and causing malfunctions. Army manual calls for the castle nut to be torqued to 38 to 42ft/lb, and staked in two places. While we're not in the "more is better, bigger is better" camp, there are times less isn't more. The TDP spec castle nut is a simple and robust fastener that is almost perfect for the job it's tasked to perform. Over the years, we've consistently come up with two minor gripes, first is its staking notches seem rather shallow and short, second is we don't enjoy using the castle nut's wrench notches as serrations (our fingers invariably find their way to these sharp cutouts) to rotate it towards to the end plate while installing it. CNF (Castle Nut, Forward Controls) is based on the TDP spec castle nut, with couple of changes: 1. Staking notches angle changed from 45 to 30 degrees, this results in longer (25% longer than TDP spec) and deeper notches than found on TDP castle nuts. 2. Number of staking notches increased from 3 to 4, spaced equally on the CNF. The castle nut is to be staked in two places, we're not advocating staking in more than two places, CNF's 4 staking notches mean that, at all times, 3 will be visible and available for staking, it simply gives the user more staking location options. 3. Coarse serrations on the wrench side of the nut, a single use feature to make it easier while rotating the CNF towards the end plate. It is our opinion that a castle nut should be staked per TM, CNF's longer and deeper notch reinforces the belief, that once installed and staked, it will not loosen without the user's deliberate action. We love the idea of quick detach, but some things on an AR are meant to stay put, and considerable effort was made to ensure that by the original designers. CNF is a continuation and evolution in that direction. CNF is billet machined in 4140 PH steel, and black nitrided (Cerakoted FDE, OD green, and burnt

maximdefense.com

At Maxim Defense we're dedicated to the design and production of only the highest grade in performance firearms, suppressors, and accessories for both the Commercial and Special Operation markets.

triarcsystems.com

Buy the TRI-ARCA Rail Attachment Plate with M-LOK and R-Lock. This TRI-ARCA Rail is based on the popular Arca-Swiss quick-release system. Learn more about some of our great added features.

primaryarms.com

Back Details Designed for real-world use, the Maxim Defense CQB Gen 6 Pistol Brace for AR-15 offers both comfort and durability. When fully collapsed, this brace adds minimal length to any AR-15 pistol. The CQB Gen 6 offers four adjustable positions, making it versatile and suitable for a wide range of shooting needs. The CQB Gen 6 deploys swiftly and intuitively without any cumbersome buttons to push. Made from tough materials, this brace features a 3.3 oz buffer and is one of the toughest and most adaptable CQB braces for the AR-15. Features: Adjustable pistol brace for AR-15 Rugged, lightweight construction Adds minimal overall in the collapsed position 3.3 oz buffer included Color: black Highly compact and maneuverable pistol brace Easy to adjust length of pull Sling mounting slots See More

bravocompanyusa.com

KAG-MCMR (M-LOK® Compatible*) Kinesthetic Angled Grip - KAG The KAG is the end result of collaboration between BCM® and Travis Haley, founder of Haley Strategic Partners and inventor of multiple weapons manipulation enhancements in the firearms industry. Designed to complement modern shooting grips, the Kinesthetic Angled Grip (KAG) uses a biomechanically efficient forward rake to create an interface for positive retention and joint relief to the wrist, elbow, and shoulder, allowing for smooth weapon manipulation without substantial increase to the girth of the weapon system. Textured on both front and back, the profile of the KAG creates a channel for consistent and positive engagement which translates directly into improved efficiency in weapons manipulation and target to target transitions. Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support Works as a rest for supported firing positions Slight angle without significant bulk adds just the right amount of relief to the wrist without substantially increasing the girth of the handguard Small profile is just enough to get repeatable hand position on weapon forend Textured in front and back for positive engagement Made in the U.S.A. from high quality, impact resistant polymers. * M-LOK® is a registered trademark of Magpul Industries Corp. https://www.magpul.com/ip

magpul.com

shop magpul for high-quality firearms accessories & tactical gear. browse our selection of stocks, grips, magazines, and more. free shipping on orders over $75.

armalite.com

What's the Status of My Order? When placing an online order for your ArmaLite Rifle or Official ArmaLite Apparel, you will be provided the status of the item to inform you if the item is in-stock, out-of-stock, or on back order. For all online orders, you will be contacted within 24 hours by a member

dpmsystems.com

<p><strong>DPM Mechanical Recoil Reduction System for Glock Models: 17-22-31-34-35-37 Gen 5</strong></p><ul><li>9 Adjustable User Settings</li><li>Stainless Steel (Black Oxide) Spring Plugs</li><li>Designed to serve Competition, Standard and Heavy Ammo</li></ul><p>**As we lead the evolution of recoil reduction technology, products may change versions (new design with different springs, with or without plugs, washers, etc.) without any prior notice.** </p><p><strong>Advanced Recoil Control</strong><br></p><p><strong>Competition Ammunition: </strong>Small washer with Small/Soft or Medium Spring</p><p><strong>Factory Ammunition: </strong>Medium washer with Medium or Long/Heavy Spring</p><p><strong>Heavy Ammunition +P: </strong>Long washer with Long/Heavy or Medium Spring</p><p>Feel free to try any possible combination of washer and spring with your ammunition.</p><p><strong>Spring Force (measured in pounds) </strong></p><p>Slide in battery</p><ul><li>Short Spring: <strong>8 lb</strong></li><li>Medium Spring: <strong>9 lb</strong></li><li>Long Spring: <strong>10 lb</strong></li></ul><p>* The forces are slightly increased depending the length of the Washer.</p><p><strong>Slide fully open (approx.):</strong></p><ul><li>Short Washer: <strong>14 lb</strong></li><li>Medium Washer: <strong>18 lb</strong></li><li>Long Washer: <strong>20 lb</strong></li></ul><p><strong>Overall Advantages</strong></p><p></p><ul><li>Faster follow up shots</li><li>